Foshan Nanhai Jinsumei Environmental Protection Plastic Product Co., Ltd.
Products
Rotomolded Fuel Tank for Compact Tractors
Fuel Tanks Series
Description
Product Overview
On a compact tractor or a riding machine, the fuel tank lives under the hood or the seat, where the bodywork slopes on every side. A box tank leaves its corners empty and sits too high. The tank that fits that position is a wedge.
This tank is rotomolded from cross-linked polyethylene as a single piece. The body tapers from a tall rear section down to a low nose, following the hood line instead of fighting it, so the same space holds more diesel and the tank sits out of sight under the panel. There is no seam anywhere on the body, and no bracket to fabricate.
For a machine with a flat deck position instead of a sloping one, compare the low-profile flat tank; for a small off-road body with a textured flank, the textured fuel tank.
How the Wedge Shape Works
The taper is what buys the fit. The rear of the body rises to the filler dome, which stands at the highest point of the molding, so the tank fills completely without trapping air and the screw cap stays reachable when the hood opens. Forward of the dome, the body drops away to clear the engine and the steering column underneath.
A deep recess is molded into the flank. On most installations it passes over a frame rail or a cable run, which lets the body sit lower than a flat-walled tank could, and it divides the side face into shorter spans so the wide panel does not bulge when the tank is full. If your machine clears a different member there, send its position and the recess is set from your drawing.
Filling and Mounting
The filler dome carries a screw cap with a seal, and a small secondary port beside it takes the vent or the return line. Outlet and drain bosses are placed from your engine layout, each formed with reinforced material so the fittings thread into real wall thickness rather than a thin panel.
Mounting points are molded into the base and the rear face, positioned from your bracket drawing. The tank bolts straight onto the mounts the machine already has. No cradle, no straps, and no drilling after the part leaves the mold.
Because the tank sits low in the machine, fuel behavior on a slope stays predictable: the pickup stays covered longer than in a tall, narrow body of the same capacity. Machines that run several circuits at once can move up to the multi-port version.
Product Specifications
| Spec | Value |
|---|---|
| Product | Rotomolded Fuel Tank for Compact Tractors |
| Material | Cross-linked polyethylene (XLPE) |
| Process | Rotational molding, one-piece body |
| Shape | Wedge body, tapering from the filler dome to a low nose |
| Filler | Screw cap on a raised dome, highest point of the molding |
| Flank | Deep molded recess for frame or cable clearance |
| Ports | Vent or return beside the dome; outlet and drain per drawing |
| Mounting | Molded-in inserts at the base and rear face |
| Application | Compact tractors, riding mowers and utility machines |
| Capacity | Set by the drawing |
Why Rotational Molding
A tapered tank under a hood takes vibration from the engine on one face and shock from the axle on another. A welded steel body concentrates that load at its seams; rotomolding forms the wedge, the dome, the flank recess and the bosses in one cycle, so the wall stays continuous through every change of angle. The tooling is a casting of your geometry, which keeps the mold affordable even for a body this specific.
What to Send Us
The mounting envelope matters more than anything else. Send a drawing or 3D model of the space with the fixing points and whatever the flank recess has to clear, plus the capacity you need, the port list with fitting sizes, and the cap specification if your machine uses a defined one. If the only reference is the used tank you are replacing, send that and we will work back from it.
Where the frame allows a square body, the square tank for machinery is simpler and cheaper.
FAQ
1. Can the tank be made to fit our hood line exactly?
Yes. Send the space drawing or 3D model with the fixing points, and the taper, dome position and recess are set from that geometry. The fit is settled on paper before the mold is cut.
2. Is XLPE needed, or will LLDPE work?
Both are used for diesel tanks. Cross-linking gives the wall better resistance to heat and to the hydrocarbons in diesel. For a tank mounted close to the engine under a hood, XLPE is the safer choice.
3. Can the flank recess be left out?
Yes. The recess exists to clear a frame member and stiffen the face. If your mounting position has nothing to clear, the body is molded with a plain flank and the stiffening moves into the wall.
4. Will the tank take a fuel gauge sender?
Yes. The sender boss is molded to your flange pattern. Send the sender drawing or the bolt circle and we will match it. Where the machine needs two liquids in one bay, the dual compartment tank splits the volume instead.
Keywords:
Product inquiry
Note: Please leave your phone number or E-mail and our professionals will contact you as soon as possible!