Rotomolded Rooftop Cargo Box 110L


110 L rooftop cargo box rotomolded in PE: one-piece shell, three latch points, recessed handles, wheels and a quick-release base.

Category:

Various rotational molding box series

Description

This 110 L rooftop box is rotomolded from PE in one piece, so the shell has no seam to split along and the wall thickness stays consistent across the lid and the body. It is built for the trips where the boot runs out first: camping gear, tools, a spare set of wheels, or luggage for four people. Jinsumei moulds the shell in-house and supplies the latches, quick-release base plate and mounting hardware with it, which means one supplier and one set of tolerances for the whole assembly.

Specifications

External dimensions145 × 45 × 30 cm
Capacity110 L
ShellPE, rotomolded, one-piece
Latch points3, along the lid edge
Handles2 recessed handles, one at each end
WheelsFitted, for moving the box on the ground when it is off the car
MountingQuick-release base plate, mounting hardware included
FinishIn-mold texture; colour and molded-in graphics to order

Why a rotomolded shell instead of a thermoformed one

Rotomolding suits a part this size because the mould fills as one closed volume: the powder melts against the tool wall and builds a uniform skin, so the lid and body come out as single seamless pieces rather than two sheets welded or bonded together. For a roof box that lives outdoors, that matters at the corners and around the latch bosses, where a seam is the first place to fail.

Tooling is also cheaper than injection moulding at low and medium volumes, which is why rotomolding is the usual route for roof box programmes that start with a few hundred units and grow. The trade-off is cycle time — a rotomolded shell spends longer in the mould than an injected one — so it is the right process for large parts and moderate volumes, not for high-volume small components.

Graphics and logos are molded into the surface during the same cycle, so there is no decal to peel off and no print to fade. Colour is pigmented through the material rather than painted on top, so scratches show the same colour underneath.

Lid, latches and everyday handling

Three latch points pull the lid down along its edge, which keeps the lid flat against the body instead of bowing in the middle. The lid overlaps the body flange, so rain runs off the joint rather than sitting in it.

Two recessed handles sit at the ends of the box. They are molded into the shell, not bolted on, so there is nothing to work loose, and they stay out of the way of the roof bars. When the box comes off the car, the fitted wheels let one person roll it to the garage or the tent instead of carrying 110 L of gear by hand.

Mounting

The box sits on a quick-release base plate that clamps to standard roof crossbars. The plate is designed to release without tools, so the box can come off between trips and the bars stay on the car. Mounting hardware is included with every box. If you are matching the box to a specific vehicle, check the crossbar spread and the roof width against the 145 cm length before ordering.

OEM and ODM options

  • Shell colour matched to your range, pigmented in the material
  • Molded-in logo and graphics, no separate decal step
  • Latch and base plate hardware selected to your market
  • Retail packaging and carton marking to your specification
  • Sampling from the existing mould before any tooling change

Jinsumei has been rotomolding for over ten years and holds ISO 9001:2015 and FDA 21 CFR 177.1520 certification. Our product range covers fuel tanks, hydraulic tanks, water tanks, storage boxes and roof boxes, so a roof box programme can share material and process knowledge with parts we already run.

Questions buyers ask

How much fits in 110 L?

Roughly two to three soft duffel bags, or a tent, two sleeping bags and a stove. The 145 cm length takes long items such as ski bags and fishing rod tubes that will not go in the boot.

Will it fit my car?

It fits vehicles with roof crossbars. Measure the distance between your bars and the usable roof width, then compare with the 145 × 45 cm footprint. Cars without bars need a bar kit first.

Can the box be locked?

The three latch points hold the lid closed. If your market expects a keyed lock, tell us at the enquiry stage and we will quote the latch option that fits.

Can we put our own brand on it?

Yes. Logos and graphics are molded into the shell, and shell colour is pigmented to your reference. Both are set at the tooling or production stage, so they are agreed before the first batch.

What is the minimum order and lead time?

Both depend on colour, hardware and packaging, so we quote them per project rather than publishing a single number. Send your target volume and market and we will come back with the details.

Request a quote

Send us your drawing or reference sample, the volume you expect in the first year, and the market you sell into. We will reply with tooling requirements, unit pricing and the sampling plan. WhatsApp +86 180 2493 9678 or email us through the contact form.

Product inquiry

Note: Please leave your phone number or E-mail and our professionals will contact you as soon as possible!