Rotomolded Conical Marker Buoy


A conical marker buoy molded as a single sealed polyethylene body, with a molded rope eye at the nose. The cone shape does two jobs on the water: it sheds wave and current load rather than slapping against it the way a flat-faced float does, and it gives a clear directional read from a distance, which is what a channel marker or a lane boundary needs. Being one-piece polyethylene, there is no seam, no foam fill and nothing to corrode.

Category:

Water activity facility series

Description

Product Overview

The buoy body is rotationally molded as a hollow closed shell. Buoyancy comes from the sealed air volume, not from foam, so the buoy does not gain weight over time as foam takes on water — the failure mode that takes older floats out of service. The nose eye is molded in, so the mooring or line load is carried through the wall itself rather than through a bolted-on eye that could work loose.

Supplied in a single molded color. Because color is compounded into the material, the buoy stays legible in service without repainting — the maintenance point that matters most for markers spread across a channel.

Applications

  • Channel and lane marking: navigation edges, swimming areas, regatta courses.
  • Mooring and pick-up points: line anchors for small craft and dinghies.
  • Aquaculture: position and boundary markers for nets, cages and longlines.
  • Marine construction and dredging: temporary marking of works and cables.
  • Barrier and boom lines: float support along containment lines.

Material & Manufacturing

  • LLDPE / HDPE body: LLDPE where impact flexibility matters on a buoy that gets bumped by boats; HDPE where a stiffer wall is preferred.
  • One-piece molding: the cone is a single closed shell — no cap, no joint at the nose.
  • Seamless wall: no wetted seam or fastener line; the only opening is the molded line eye.
  • Wall thickness: set against the required buoyancy and the load the eye has to carry; heavier at the nose and base contact zone.
  • UV-stabilized compound: stabilizer and pigment in the resin, chosen for permanent outdoor exposure.

Structural Design

  • Sealed buoyancy chamber: air volume determined by the target buoyancy and the freeboard you want under load.
  • Cone profile: reduces slapping and gives directional readability; the taper also lets buoys nest for storage and shipment.
  • Molded eye: line attachment formed in the mold at a thickened section, so the load path runs through the shell.
  • Base: flattened or reinforced for stability at the waterline and to resist abrasion when the buoy is dragged.
  • Ballast and mooring: where a buoy must hold station rather than drift, the mooring arrangement is agreed with the buoyancy figure — the two cannot be specified separately.

Quality Inspection

  • Water-fill check: body filled and observed, so any seepage at the eye or a molded insert shows up before shipment.
  • Leak check at the eye: attachment point checked individually — it is the one place a line load concentrates.
  • Visual inspection: color consistency, surface finish and cone symmetry against the approved sample.
  • Dimensional check: height, base diameter and eye position against the drawing.
  • Wall thickness sampling: nose, mid-cone and base.

OEM & ODM

  • Size and volume: cone height and base diameter adjusted to your buoyancy requirement.
  • Fittings: eye position, through-rope arrangement, swivel or shackle interface, reflective banding, and molded lettering or numbering.
  • Color: molded-in color; two-color bodies and banded designs are feasible depending on the mold.
  • New shapes: from drawings or a reference buoy; moldability reviewed before tooling is quoted.
  • Sampling: first samples approved before production. Other flotation shapes: water activity facility series.

FAQ

Will it stay buoyant long term?

The shell is sealed and hollow, so buoyancy does not depend on foam that can absorb water. As long as the shell is intact the air volume stays the same; that is why the eye and any insert are checked before shipment.

Can it be moored in a current or tidal flow?

Yes, but the line load and the buoy's station-keeping need to be planned together. Tell us the flow, depth and mooring chain weight so the buoyancy figure is set with a real freeboard margin.

Does it need a reflective band?

Commonly specified for night visibility. It can be added as a separate component or worked into the mold design depending on volume.

What color should we choose?

Color is a functional decision on the water, not only branding: contrast against the background and against other markers matters. We can supply standard colors or match a specified one.

Product inquiry

Note: Please leave your phone number or E-mail and our professionals will contact you as soon as possible!